|
CERA-FOIL–The heat stops here! |
|
|
CERA-FOIL® provides hot face
insulating barrier protection that stops heat
transfer through and around venting systems. This
reduction in heat transmission reduces fuel
consumption, chimney deposits, moisture
condensation, and promotes a strong draft signal,
via virtually instantaneous flue liner heat up. CERA-FOIL®
was introduced in 1986 as an advanced insulating
medium in conjunction with our 304-L
and 316-L based SUPER FLEX® Flexible Relining
System. CERA-FOIL® offers obvious advantages over
other insulating methods. |
|
|
|
|
|
|
FEATURES:
Total fiber containment, easy installation
Available in three custom factory trimmed widths, minimizing waste, cost, and time.
Light weight, no settling.
No curing time, not affected by moisture or temperature.
4” foil equivalent to 12” of Vermiculite based on insulating slurry.
Will not break down from extreme temperatures or thermal cycling.
Always allows for proper thermal expansion.
Foundry pre-trimmed for 6, 7, 8 inch diameters.
APPLICATIONS:
- Insulation of stainless steel chimney liners, both flexible and rigid.
- Wrapping clay flue tile on new masonry construction, reducing condensation and allowing room for thermal expansion.
- Insulating the sides and rear of fireplace inserts, and preventing heat loss through back firebox wall.
- Effective and durable gasketing when used to seal fireplace insert faceplates.
- Heat shielding stovepipe from combustibles.
- Sealing thimbles and damper frames.
- Insulating top plates and chimney caps.
- Packing the first flue tile area or top of smoke chamber, creating a heat proof seal when installing a new fireplace stainless steel flue liner.
|
|
Six Easy Steps That Revolutionized Flue Liner Insulating
1. Apply glue to fiber face.
2. Overlapping one inch past seam, press blanket into place.
3. Apply 8 wide horizontal laces approx. 1-2 ft. apart.
4. Apply a continuous vertial length of metal seam tape over lacing end to end. Apply tape around top and bottom ends of CERA-FOIL® creating a complete aluminum encapsulation.
5. Apply skin clamps at each end, clamping skin to stainless liner surface.
6. With stainless wire affixed around clamp, apply wire in a candy can stripe, tying off at opposite clamp.
| | |
|
Thick W
L
1/2" = zero/zero |
4" 5"
6" |
|
1/4" x 24" x 25'
1/2" x 24" x 25'* |
$157.60 add
|
$231.00
add |
|
1/4" x 24" x 30'
1/2" x 24" x 30'* |
$185.80
add |
$274.90
add |
|
1/4" x 24" x 35'
1/2" x 24" x 35'* |
$219.20
add |
$319.90
add
|
|
1/4" x 24" x 40' |
$249.70
add |
| |
7" |
|
1/4" x 25 1/2"x 25'
1/2" x 25 1/2"x 25'* |
$177.80
add
|
$302.00
add
|
|
1/4" x 25 1/2"x 30'
1/2" x 25 1/2"x 30'* |
$221.60 add
|
$363.00
add |
|
1/4" x 25 1/2"x 35'
1/2" x 25 1/2"x 35'* |
$266.40
add
|
$423.20
add |
|
• 1" x 24" x 25' |
$469.88
add |
|
• 1" x 24" x 25' No
face |
$193.30
add |
| |
8" |
|
Thimble Wrap
1/2" x 12" |
$143.80
add |
|
1/4" x 29" x 25'
1/2" x 29" x
25'* |
$207.90
add |
$297.50
add |
|
1/4" x 29" x 30'
1/2" x 29" x 30'* |
$237.22
add |
$357.90
add |
|
1/4" x 29" x 35'
1/2" x 29" x 35'* |
$282.50
add |
$415.40
add
|
|
1/4" x 29" x 40' |
$325.40
add |
|
•
1" x 24" x 25' |
$469.88
add |
|
• 1" x
24" x 25' No face |
$193.30
add |
| |
9" |
|
1/4" x 36" x 25'
1/2" x 36" x
25'* |
$283.20
add
|
$374.20
add |
| |
10" 14" |
|
1/4" x 48" x
25'
1/2" x 48" x 25'* |
$359.80
add |
$539.00
add
|
|
Prices are U.S and subject to change
depending on market conditions |
| |
*PRODUCT NOTE: 1"
Cera Foil blankets are used exclusively to wrap and
insulate the firebox, flares, hearth and smoke
chamber
• Also use with BCC Zero clearance Series
1/2" thickness Cera Foil 3 mil. foil face ceramic
blankets provide zero/zero thermal protection with
single wrap application. The industry standard. |
| |
 |
CERA-FOIL®
Adhesive
Metal Seam
Tape |
 |
GLUE: 16 oz.
spray/Blanket
Adhesive |
 |
SS WIRE
Type 304/18
Gauge/200 ft. |
|
|
$29.00
add |
|
$23.90
add |
|
$25.70
add |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
 |
|
| |
|
|
|
|
|
|
| |
|
|
|
|
|
|
